Inconel 625 Fasteners – UNS N06625 Stud Bolts, Bolts, Nuts & Washers

Unifit Fastener manufactures and supplies Inconel 625 fasteners (Alloy 625, UNS N06625 / W.Nr. 2.4856) for joints that face seawater, acids, sour gas or high heat. Our range covers stud bolts and threaded rods, hex and heavy hex bolts, nuts, socket cap screws and washers, made to ASTM F468 (bolts and studs) and ASTM F467 (nuts) from ASTM B446 bar.

Alloy 625 gets its strength from molybdenum and niobium rather than from age hardening. In the annealed condition it gives 120 ksi minimum tensile strength and still resists pitting, crevice corrosion and chloride stress cracking where 316 and duplex bolting fail. That’s why it’s the standard choice for subsea flanges, offshore piping and chemical plants. For flange work, we make single-end and double-end Inconel 625 stud bolts in metric and inch sizes, with custom lengths to your drawing.

Unifit is ISO 9001:2015 certified and has made nickel-alloy fasteners in Mumbai since 2014. Every consignment ships with an EN 10204 3.1 material test certificate. Need a different grade? See our full Inconel fasteners range.

Request Quote

Alloy 625 (UNS N06625) Fastener Specification

Item Detail
Alloy Inconel 625 / Alloy 625 / UNS N06625 / W.Nr. 2.4856 / NiCr22Mo9Nb
Fastener standards ASTM F468 / F468M (bolts, screws, studs), ASTM F467 / F467M (nuts)
Bar / forging ASTM B446 / ASME SB-446 (Grade 1 annealed, Grade 2 solution annealed); ASTM B564 forgings; AMS 5666
Sizes F468 range 1/4" – 1-1/2" (M6 – M36); larger studs and bolts to B446 / drawing up to 4" / M100 
Stud lengths Up to 3,000 mm 
Threads UNC, UNF, 8UN, metric coarse/fine, BSW
Sour service NACE MR0175 / ISO 15156, 35 HRC max
Certification EN 10204 3.1 standard; 3.2 by SGS, TÜV, BV or Lloyd's
HSN code 7318 (some exporters use 7508; confirm with your customs broker)

Inconel 625 Stud Bolts 

Inconel 625 stud bolts are the most-ordered Alloy 625 fastener for flange bolting in subsea, offshore and chemical plants. We make:

  • Fully threaded stud bolts to ASME B16.5 / B16.47 flange tables, with 2 heavy hex nuts each
  • Double-ended and tap-end studs, and reduced-shank studs
  • Continuous threaded rod, cut to length
Item Detail
Material ASTM B446 Grade 1 (annealed) bar, F468 properties. See our Alloy 625 round bar (ASTM B446)
Diameters 1/2" – 4" / M12 – M100 
Threads UNC to 1", 8UN above 1" (ASME B1.1), metric to ASME B1.13M
Ends Chamfered both ends; full or partial thread
Nuts Inconel 625 heavy hex nuts to ASTM F467 
Coating Xylan 1070 or PTFE for anti-galling (recommended: 625 on 625 can gall)
Marking Grade, heat number and manufacturer mark on one end

Also see our full range of Inconel stud bolts.

Inconel 625 Fastener Product Range 

Inconel 625 Bolts

Inconel 625 bolts

hex, heavy hex, socket cap screws. 

Inconel 625 Nuts

Inconel 625 nuts

hex, heavy hex, lock nuts. 

Inconel 625 Washers

Inconel 625 washers

flat, spring, lock. 

Inconel 625 Screws

Inconel 625 screws

machine, set and socket screws

UNS N06625 Chemical Composition (ASTM B446)

Element Content (%) per ASTM B446
Nickel (Ni) 58.0 min
Chromium (Cr) 20.0 – 23.0
Molybdenum (Mo) 8.0 – 10.0
Niobium + Tantalum (Nb + Ta) 3.15 – 4.15
Iron (Fe) 5.0 max
Cobalt (Co) 1.0 max
Carbon (C) 0.10 max
Manganese (Mn) 0.50 max
Silicon (Si) 0.50 max
Aluminium (Al) 0.40 max
Titanium (Ti) 0.40 max
Phosphorus (P) / Sulphur (S) 0.015 max each

Alloy 625 Bolt Mechanical Properties: Grade 1 vs Grade 2

Condition (ASTM B446) Tensile, min Yield (0.2%), min Elongation, min Typical use
Grade 1 – Annealed (≤ 4") 120 ksi (827 MPa) 60 ksi (414 MPa) 30% Service up to ~593 °C (1100 °F); standard for fasteners
Grade 2 – Solution annealed 100 ksi (690 MPa) 40 ksi (276 MPa) 30% Above ~593 °C, where creep and rupture strength matter

Need 625 stud bolts for a flange schedule? Send the flange size, class and quantity; we quote studs with matching 625 nuts and a 3.1 MTC within 24 hours.

Request Quote

Inconel 625 Stud Bolt and Heavy Hex Nut Dimensions

Stud bolts are threaded UNC up to 1" and 8UN above 1", per ASME B1.1. The nuts are Inconel 625 heavy hex nuts to ASTM F467, with dimensions per ASME B18.2.2.

Stud diameter Threads per inch Thread series Nut width across flats Nut height
1/2" 13 UNC 7/8" (22.2 mm) 31/64" (12.3 mm)
5/8" 11 UNC 1-1/16" (27.0 mm) 39/64" (15.5 mm)
3/4" 10 UNC 1-1/4" (31.8 mm) 47/64" (18.7 mm)
7/8" 9 UNC 1-7/16" (36.5 mm) 55/64" (21.8 mm)
1" 8 UNC 1-5/8" (41.3 mm) 63/64" (25.0 mm)
1-1/8" 8 8UN 1-13/16" (46.0 mm) 1-7/64" (28.2 mm)
1-1/4" 8 8UN 2" (50.8 mm) 1-7/32" (31.0 mm)
1-3/8" 8 8UN 2-3/16" (55.6 mm) 1-11/32" (34.1 mm)
1-1/2" 8 8UN 2-3/8" (60.3 mm) 1-15/32" (37.3 mm)
1-3/4" 8 8UN 2-3/4" (69.9 mm) 1-23/32" (43.7 mm)
2" 8 8UN 3-1/8" (79.4 mm) 1-31/32" (50.0 mm)

Inconel 625 vs 718 vs 600 Fasteners

  Inconel 625 Inconel 718 Inconel 600
UNS N06625 N07718 N06600
Strengthening Solid solution (Mo, Nb) Age hardened Solid solution
Yield, min (typical fastener) 60 ksi 150 ksi 35 ksi
Chloride/seawater resistance Excellent (PREN ≈ 50) Good Moderate
Hydrogen embrittlement under CP Low risk (annealed) Higher risk Low
Best for Corrosive, subsea, sour service High-load bolting, high temperature Oxidation, high temperature

See Inconel 718 fasteners and Inconel 600 fasteners.

Technical Data

Physical Properties of Inconel 625

Property Metric Imperial
Density 8.44 g/cm³ 0.305 lb/in³
Melting range 1290 – 1350 °C 2350 – 2460 °F
Curie temperature Below -196 °C Below -320 °F
Relative magnetic permeability 1.0006 (at 15.9 kA/m) 1.0006 (at 200 Oe)
Modulus of elasticity 207 GPa 30.0 × 10³ ksi

Inconel 625 Equivalent Grades

Standard Country / Region Designation
UNS USA N06625
Werkstoff Nr. Germany / Europe 2.4856
EN Europe NiCr22Mo9Nb
AFNOR France NC22DNB4M
JIS Japan NCF 625
BS United Kingdom NA 21
GOST Russia XN75MBTYu

Where Are Inconel 625 Fasteners Used?

Most bolting can handle either corrosion or heavy load. Alloy 625 handles both at once, which is why engineers specify it for joints where a failure would mean shutting down a plant, losing a subsea well, or sending divers down to replace corroded studs. Here’s where our Inconel 625 fasteners end up:

  • Subsea and offshore oil & gas: Flange studs on manifolds, Xmas trees and risers. 625 holds up in seawater and stays safe under cathodic protection, where age-hardened alloys can crack.
  • Sour service and refining: Bolting for H2S and CO2 environments, supplied to NACE MR0175 / ISO 15156 at 35 HRC max.
  • Marine and shipbuilding: Seawater pumps, cooling systems, ballast lines and deck hardware, where 316 and even duplex bolts suffer from crevice corrosion.
  • Chemical and petrochemical plants: Reactors, heat exchangers and acid lines handling phosphoric, sulphuric or mixed acids.
  • Power and pollution control: Flue gas desulphurisation scrubbers and stack components, where hot, wet acidic gas eats through ordinary steel.
  • Aerospace: Exhaust ducting and engine hardware that has to keep its strength through repeated heating and cooling.
  • LNG and cryogenic service: 625 stays tough well below zero, so it’s used on cold-end flanges and storage equipment.

If you’re bolting flanges, start with our Inconel stud bolts and pair them with matching Inconel 625 nuts and Inconel 625 washers. That keeps the whole joint in the same alloy and avoids galvanic corrosion.

Quality, Testing and Delivery 

Every Inconel 625 fastener is made from mill-certified B446 bar, hot forged (M24+) or cold formed, with rolled threads. We test chemistry (PMI on 100% of the pieces in each lot), tensile and hardness, IGC to ASTM G28 Method A, and dimensions, and ship with an EN 10204 3.1 MTC. Ready-stock sizes dispatch in 2–5 working days; custom sizes in 2-4 weeks. 

See all our nickel alloy fasteners.

FAQs Inconel 625 Fasteners 

What standard covers Inconel 625 fasteners?

ASTM F468 covers Inconel 625 bolts, screws and studs; ASTM F467 covers the nuts. The bar is ASTM B446, and forgings are ASTM B564.

What is the difference between Grade 1 and Grade 2 Inconel 625?

Grade 1 is annealed, with higher strength (120 ksi tensile), and is used up to about 593 °C. Grade 2 is solution annealed, with lower room-temperature strength but better creep resistance above 593 °C.

Are Inconel 625 fasteners NACE MR0175 compliant?

Yes, when supplied in the annealed condition at 35 HRC maximum, as NACE MR0175 / ISO 15156 requires. Compliance is stated on the MTC.

Inconel 625 or 718 for stud bolts?

718 has about 2.5× the yield strength and suits high-load bolting. 625 has better corrosion resistance and lower hydrogen-embrittlement risk under cathodic protection, so it's often chosen for subsea and seawater service.

Do Inconel 625 bolts gall?

Yes, like most nickel alloys. Use an anti-seize compound, or order Xylan or PTFE-coated studs or nuts.

Are Inconel 625 fasteners magnetic?

No. Alloy 625 is non-magnetic.

What is the HSN code for Inconel 625 fasteners?

Indian exporters commonly use HSN 7318 for threaded fasteners. Some classify nickel-alloy articles under 7508. Confirm with your customs broker.

What sizes of Inconel 625 stud bolts do you supply?

From 1/2" to 4" and M12 to M100, in lengths up to 3,000 mm, with threads to UNC, 8UN or metric.