Inconel 600 Fasteners (UNS N06600): Bolts, Nuts, Studs and Washers

Inconel 600 Fastener Manufacturer in India

An Inconel 600 fastener is made from Alloy 600 (UNS N06600, W.Nr 2.4816, NiCr15Fe), a nickel chromium iron alloy with 72% minimum nickel, 14.0 to 17.0% chromium and 6.0 to 10.0% iron. These Inconel 600 fasteners resist oxidation up to 1093 degrees C (2000 degrees F), with an annealed tensile strength of 80 ksi (550 MPa) minimum, a yield strength of 35 ksi (240 MPa) minimum and a density of 8.47 g per cm3. Unifit Fastener, an Inconel fasteners manufacturer, supplier and exporter in India. We make UNS N06600 (Alloy 600) bolts, including Inconel 600 bolts in hex and heavy hex styles, plus Inconel 600 stud bolts, threaded rod, nuts and washers.

Request a Quote

Technical Data

Specifications of Inconel 600 Fasteners

Parameter Details
Specifications Bolts, studs and screws: ASTM F468. Nuts: ASTM F467 (ASME SF467). Raw material: ASTM B166 bar, rod and wire; ASTM B564 forgings; ASTM B168 plate and sheet for washers.
Sizes nuts, studs, screws and washers M3 to M56 and 3/8 inch to 2 inch; machine screws M1.6 to M12; custom sizes on request
Dimensional standards ISO, DIN and ASME B18 series as drawn
Bolt Dimensions 3 mm to 200 mm, with non standard dimensions available on request
Nut Dimensions M3 to M56, 3/8 inch to 2 inch, with custom dimensions available
Screw Dimensions M3 to M56, 3/8 inch to 2 inch, including made to order sizes
Machine Screw Dimensions M1.6 to M12, with special dimensions available
Washer Dimensions M3 to M56, 3/8 inch to 2 inch, including custom dimensions
Available Fastener Types hex, heavy hex and square nuts, coupling nuts, domed cap nuts, hex head bolts, stud bolts, threaded rod, socket head cap screws, set screws, machine screws, spring and flat washers. Bolts are covered on our Inconel 600 bolts page

Chemical Composition of Inconel 600 Fasteners 

Grade C Mn Si S Cu Fe Ni Cr
Inconel 600 0.15 max 1 max 0.50 max 0.015 max 0.50 max 6 – 10 72.00 min 14 – 17

Inconel 600 Fastener Mechanical Properties 

Property Value
Tensile Strength (Min) 80 ksi (550 MPa)
Yield Strength 0.2% Offset (Min) 35 ksi (240 MPa)
Elongation (%) 30% Min
Density 8.47 g/cm³

International Equivalent Grades of Inconel 600

Standard Werkstoff Nr. UNS JIS BS GOST AFNOR EN
Inconel 600 2.4816 N06600 NCF 600 NA 13 МНЖМц 28-2,5-1,5 NC15FE11M NiCr15Fe

Types of Inconel 600 Fasteners

Inconel 600 Bolts

Inconel 600 Bolts

Hex and heavy hex bolts to ASTM F468 for high-temperature joints.

Inconel 600 Nuts

Inconel 600 Nuts

Hex and heavy hex nuts to ASTM F467, matched to Inconel 600 bolts.

Inconel 600 Washers

Inconel 600 Washers

Flat and spring washers that resist oxidation at high heat.

Inconel 600 Screws

Inconel 600 Screws

Machine and socket cap screws for heat-exposed assemblies.

Applications of Inconel 600 Fasteners

  • Heat treatment and thermal processing: muffles, retorts, baskets, trays and furnace hardware need fasteners that survive scaling.
  • Chemical processing: heat exchangers, evaporators and condensers in caustic and chloride service.
  • Aerospace and gas turbine: engine and exhaust components that see high temperature.
  • Pulp and paper: the alloy resists abietic acid, a documented use.
  • Food processing: sterilization and high temperature equipment.
  • Nuclear: Alloy 600 has been used in reactor components, but it can crack in primary water service, and newer steam generator designs moved to Alloy 690. It is not a blanket choice for nuclear service.

For a longer read, see our guide to the applications and uses of Inconel fasteners.

Request a Quote

Need Inconel 600 fasteners for your application? Send your drawing or size list, and we will reply with a quotation. 

Request a Quote

Frequently Asked Questions

What is Inconel 600 used for?

Inconel 600 is used for furnace hardware, chemical processing equipment, aerospace parts and thermal processing equipment, wherever heat resistance and corrosion resistance are needed together.

What is the maximum temperature for Inconel 600 fasteners?

Inconel 600 resists oxidation up to about 1093 degrees C (2000 degrees F). For load bearing use, the allowable temperature is lower and depends on stress and time, so confirm it with your design engineer.

What is the equivalent of Inconel 600? 

Inconel 600 is Alloy 600, UNS N06600, W.Nr 2.4816, NiCr15Fe, BS NA 13, AFNOR NC15FE11M and JIS NCF 600. They name the same nickel chromium iron alloy.

Which Inconel 600 fasteners do you make?

We make Inconel 600 bolts, studs, threaded rod, nuts, washers and screws. Bolt data sits on our Inconel 600 bolts page.

Which Inconel alloy should I choose if 600 is not strong enough?

Alloy 600 gets its strength from cold work only. For age hardened strength choose Inconel 718 or Inconel X 750, and for more severe corrosion choose Inconel 625. Tell us the medium and the temperature and we will recommend one.

Which standards and certificates do you supply?

We supply fasteners to ASTM F468 for bolts and studs and ASTM F467 for nuts, cut from ASTM B166 bar. Every order ships with an EN 10204 3.1 certificate.